Jackson DishStar HT Installation, Operation And Service Manual Download | Manualshive

Page: 12 / 68

background image

07610-004-37-13-E

5

WATER SUPPLY
CONNECTIONS:

WATER HARDNESS

HIGHER THAN

5 GPG

Before installing the unit, check packaging and machine for damage. Damaged

packaging might be an indication of damage to the machine. If there is any type

of damage to both packaging and unit, do not throw away the packaging. The

dishmachine has been inspected at the factory before shipping and is expected to

arrive in new, undamaged condition. However, rough handling by carriers or others

might result in damage to the unit while in transit. If this occurs, do not return the unit to

the manufacturer. Instead, contact the carrier and ask them to send a representative

to the site to inspect the damage and request that an inspection report be completed.

Contact the carrier within 48 hours of receiving the machine as well as the dealer that

sold you the unit.

The machine should be unboxed and removed from the pallet before installing. Open

the front door and remove all of the materials from inside. Once unpacked, verify there

are no missing parts. If a part is missing, contact the manufacturer immediately.

All plumbing connections must be made to adhere to local, state, territorial, and

national codes. The installing plumber is responsible for ensuring the incoming

water lines are flushed of debris before connecting to the machine. Note that chips

and materials from cutting processes can become lodged in the solenoid valves

and prevent them from opening or closing. Any valves that are found to be fouled

or defective because of foreign matter left in the water line, and any subsequent

damage, are not the responsibility of the manufacturer.

A water hardness test must be performed. A hardness test kit can be found on the

warning tag that is attached to the incoming plumbing connection on the back of the

machine. If water hardness is higher than 5 GPG, install a water softener or install the
optional HTS-11 (scale prevention and corrosion control). See the Plumbing Options

page for more information on the HTS-11.

If water hardness is higher than 5 GPG and a water softener is not being used, install

the HTS-11 into the water line (1/2” ID pipe size minimum) before the machine’s
incoming water connection point using copper pipe. Observe proper inlet/outlet water

directions (flow directions are molded into the top of the head). It is recommended

that a water shut-off valve be installed before installing the HTS-11 to allow access for

service. Plumb from the HTS-11 outlet to the incoming water connection point using

copper pipe (or order the 1/2” ID flexible hose kit offered by manufacturer). The water

supply must be capable of a minimum of 10 PSI “flow” pressure at the recommended

temperature indicated on the data plate.

See the Plumbing Options page for more

information on the HTS-11.

INSTRUCTIONS

INSTALLATION

INSPECTION

Do not throw away

container if damage is

evident!

UNPACKING

PLUMBING

A water hardness test

must be performed.

The plumber must flush

the incoming water line!

«
...
10
11
12
13
14
...
»

Summary of Contents for DishStar HT





































































Reviews:

No comments

Related manuals for DishStar HT

Brand: Dometic Pages: 32

Brand: NEFF Pages: 29

Brand: Fisher & Paykel Pages: 5

Brand: Bush Pages: 25

Brand: Kärcher Pages: 44

DISHDRAWER DD24SAX9

Brand: Fisher-Price Pages: 2

Brand: Dolphin Pages: 16

Brand: Samsung Pages: 80

WA16CG6886 Series

Brand: Samsung Pages: 112

WA13CG5745 Series

Brand: Samsung Pages: 48

WF702U4BK Series

Brand: Samsung Pages: 44

Brand: Caple Pages: 36

Brand: inventum Pages: 88

Brand: AEG Pages: 48

Brand: AEG Pages: 56

Brand: AEG Pages: 60

Brand: AEG Pages: 48

Brand: AEG Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands