background image

 

12

 / 

14

 

 

3.9.3 Monitoring parameter list (press P + press foot lifter key to enter) 

 

4 Error code 

4.1 Error code list 

If have Error or alarm, please check first as follows:1. Check the connection wire is connected or not; 2. 

Check the machine head is matched with the control box; 3. check reset is accurate or not. 

Error number

 

Code meaning 

Solutions 

Err-01

 

Arm shaft motor 

hardware overcurrent

 

1.    Turn off the system power, and turn it on again after 30 seconds. 
2.    Check whether the arm shaft motor encoder and electronic control are damaged 

or in other poor conditions. If so, replace them in time. 

3.    If the system still does not work properly after troubleshooting and restart. 

Please contact your local service provider or call 4008876858.

 

Err-03

 

System undervoltage

 

Disconnect the power supply of the controller and check whether the input power 
supply voltage is lower than 176V. If so, please restart the controller after the 
voltage returns to normal. If the voltage returns to normal, it still does not work 
properly after the controller starts up. Please contact your local service provider or 
call 4008876858.

 

Err-04 

Overvoltage during 

shutdown 

Disconnect the controller power and check whether the input power voltage is 
higher than 264V. If so, please restart the controller after the voltage returns to 
normal. If the voltage returns to normal, it still does not work properly after the 
controller starts up.Please contact your local service provider or call 4008876858. 

Err-05 

Overvoltage during 

operation 

Disconnect the controller power and check whether the input power voltage is 
higher than 264V. If so, please restart the controller after the voltage returns to 
normal. If the voltage returns to normal, it still does not work properly after the 
controller starts up.Please contact your local service provider or call 4008876858. 

Err-06 

Electromagnet circuit 

failure 

1.  Turn off the system power, check whether the electromagnet connection is 

correct and whether there is any loose or damaged part. If so, replace it in time. 

2.  Unplug the electromagnet    plug on the electric control to confirm whether the 

electric control is normal. If the electric control is normal, please check whether 
the electromagnetic circuits are damaged. 

3.  If the system still does not work after troubleshooting and restart. 
Please contact your local service provider or call 4008876858. 

Err-07 

Arm shaft motor 

current detection 

circuit failure 

Turn off the system power, and turn on the power again after 30 seconds to see 
whether it can work properly. Try a few times again. If the fault occurs frequently, 
please contact your local service provider or call 4008876858. 

Number 

Description 

Number 

Description 

M10 

Stitches account number 

M23 

Initial angle 

M11 

Pieces account number 

M24 

Mechanical angle 

M13 

Panel version number 

M25 

Max value for pedal forward press 

M18 

Main board version number for 

control box 

M26 

Sample value for pedal back 

M20 

Generatrix    Voltage 

M28 

Sample pedal value of trimming 

M21 

Machine speed 

M30-M37  Historical Error number 

M58 

Stepmotor Electric Angle

 

M59 

Stepmotor current value

 

Summary of Contents for ZB-A4F















Reviews: