Jabiru 2200 Overhaul Manual Download Page 39

Page: 39 / 201

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

6 7

Dated : 28/10/2014

Issued By: AS

Page: 39 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

Figure 42

– Safety Wire Details

Figure 43

– Safety Wire Installation Using a Twister/Pliers & By Hand

3.10 Hardware



Certain applications on the Jabiru Engine must use particular grades of hardware:

Propeller flange attach screws, flywheel attach screws, connecting rod cap screws must be
“Unbrako 1960” or “Brighton Best 1960 Grade” screws in black (not plated) finish.

Where a specific type of hardware is described

– i.e. AN4 bolts, ARP 12-point nuts – hardware must

meet the specifications for that type of hardware.

Custom hardware

– such as through bolts – must be as described in this manual.

WARNING

Failure to use correct hardware may lead to an unsafe condition.

Summary of Contents for 2200










































































































































































































Search results

Summary of Contents for 2200

Reviews:

Related manuals for 2200

Brands by name

Popular brands

Jabiru 2200, Overhaul Manual

Search results

Summary of Contents for 2200

Reviews:

Related manuals for 2200

Brands by name

Popular brands