Jabiru 2200 Overhaul Manual Download Page 174

Page: 174 / 201

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

6 7

Dated : 28/10/2014

Issued By: AS

Page: 174 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

9.9.9 Subassembly H

– Final Assembly

Table 23

– Build Sheet H

No.

Details

Para

Initials

Checked By

Date

Apply Loctite 515 to crankcase halves; lubricate where
necessary

7.8

Locate camshaft in crankcase half

7.8

Locate 2 crankcase halves over crankshaft

7.8

Stage H1 - Stage Inspection of Assembly

Apply Loctite 518 to cylinder base flanges

7.8

Tension front (2) and rear (2) crankcase studs

7.8

Place all through bolts in crankcase for cylinder bases

7.8

Fit piston and cylinder Assemblies. Check circlips

7.8

Stage H2 - Stage Inspection of Assembly

H10

Tension the cylinder base studs/bolts

7.8

H11

Fit pushrods and valve gear. Set gap per Table 12
(solid lifter engines)

7.8

H12

Apply Loctite 515 to sump sealing faces & fit to cases.

7.8

H13

Apply Loctite 515 to induction manifold sealing faces.
Assemble and fit to sump.

7.8

H14

Apply Loctite No. 2 to induction tubes & fit to induction
manifold.

7.8

H15

Check camshaft timing

7.8

H16

Apply Loctite 515 to sealing faces and fit engine mount
plate and gearbox housing

7.8

H17

Fit flywheel, alternator mount plate and ignition coils

7.8

H18

Fit Carburettor assembly

7.8

H19

Fit fuel pump. Apply Loctite 515 to sealing faces.

Apply Loctite 243 on fuel pump screws.

7.8

H20

Fit oil pump assembly. Apply Loctite 515 to sealing
faces.

7.8

Fit front seal and propeller flange. Torque per Table 9

Apply Loctite 515 to sealing faces.

7.8

Fit exhaust system

7.8

Stage H3 - Stage Inspection of Assembly

I hereby certify that the above subassembly has been assembled in accordance with the applicable Jabiru
Pty Ltd Instructions and Maintenance procedures.

Signed:

Date:

for Jabiru Aircraft Pty Ltd

Summary of Contents for 2200










































































































































































































Search results

Summary of Contents for 2200

Reviews:

Related manuals for 2200

Brands by name

Popular brands

Jabiru 2200, Overhaul Manual

Search results

Summary of Contents for 2200

Reviews:

Related manuals for 2200

Brands by name

Popular brands