iWave iW-RainboW-G7D Hardware User'S Manual Download Page 87

Page: 87 / 164

Rev 2.0

Page 87 of 164

Generic Qseven Carrier Board Hardware User Guide

iWave Systems Technologies Pvt. Ltd.

2.8.4

Sensors

The Qseven Generic Carrier Board supports 4 on board sensors,



Ambient Light Sensor



Digital eCompass



3-Axis accelerometer



Altimeter/Barometer

Below figure shows the Sensor’s physical location on the top and bottom of the board as shown below.

Figure 28: Sensors

2.8.4.1

Ambient Light Sensor

The Qseven Generic Carrier Board supports on board Ambient Light Sensor. This sensor is connected to
I2C interface of Qseven MXM connector (66

and 68

Pin) and interrupt is connected to 188

Pin of

Qseven MXM connector. This sensor (U33) is physically located on the top of the board as shown in

Figure 28

2.8.4.2

Digital eCompass

The Qseven Generic Carrier Board supports on board Digital eCompass Sensor. This sensor is connected
to I2C interface of Qseven MXM connector (66

and 68

Pin) and interrupt is connected to 186

Pin of

Summary of Contents for iW-RainboW-G7D





































































































































































Search results

Summary of Contents for iW-RainboW-G7D

Reviews:

Related manuals for iW-RainboW-G7D

Brands by name

Popular brands

iWave iW-RainboW-G7D, Hardware User'S Manual

Search results

Summary of Contents for iW-RainboW-G7D

Reviews:

Related manuals for iW-RainboW-G7D

Brands by name

Popular brands