iWave iW-RainboW-G7D Hardware User'S Manual Download Page 104

Page: 104 / 164

Rev 2.0

Page 104 of 164

Generic Qseven Carrier Board Hardware User Guide

iWave Systems Technologies Pvt. Ltd.

UART1_RXD

Output

3.3V CMOS

UART1 Receive signal.
Default NC.
Optionally Connected to Debug
RS232 transceiver through resistor
and default not populated.

UART1_CTS

Input

3.3V CMOS

UART1 Clear to Send signal.
Default NC.
Optionally Connected to Debug
RS232 transceiver through resistor
and default not populated.

GND

Power

Ground.

WIFI_PDN

Input

3.3V CMOS

Wi-Fi power down.
Connected to 63

Pin of Carrier

Expansion Connector (J10).
Optionally connected to 14

Pin of

Wi-Fi Module connector (J56)
through resistor and default not
populated.

WL_HOST_WKUP

Input

3.3V CMOS

WLAN wake up.
Connected to 59

Pin of Carrier

Expansion Connector (J10).
Optionally connected to 16

Pin of

Wi-Fi Module Connector (J56)
through resistor and default not
populated.

HOST_WL_WKUP

Output

3.3V CMOS

Host wake up.
Connected to 60

Pin of Carrier

Expansion Connector (J10).
Optionally connected to 17

Pin of

Wi-Fi Module Connector (J56)
through resistor and default not
populated

CAM_PWDN

Input

3.3V CMOS

CMOS camera power down.
Connected to 8

Pin of CMOS

Camera Connector (J51) & to 57

Pin of Carrier Expansion Connector
(J10).

Summary of Contents for iW-RainboW-G7D





































































































































































Search results

Summary of Contents for iW-RainboW-G7D

Reviews:

Related manuals for iW-RainboW-G7D

Brands by name

Popular brands

iWave iW-RainboW-G7D, Hardware User'S Manual

Search results

Summary of Contents for iW-RainboW-G7D

Reviews:

Related manuals for iW-RainboW-G7D

Brands by name

Popular brands