Iveco daily euro 4 Repair Manual Download | Manualshive

Page: 264 / 1132

background image

87792

75306

88345

90064

Figure 132

Figure 133

Figure 134

Figure 135

Take out the screws (4) and replace the phonic wheel (3).
Screws (4) shall be tightened to 10 + 1 Nm.

Replacing timing control gear

On finding the timing control gear teeth (1) damaged or
worn, remove them from the crankshaft (2) using a suitable
extractor.

The new gear is fitted onto the crankshaft by heating it to a
temperature of 180

°

C for no longer than 15 minutes.

On completing assembly and after the gear has cooled, it
must withstand a torque of 150 Nm without slipping.

ENGINE ASSEMBLY

The following parts must be replaced with new ones at the
time of assembly: retaining rings, seals and gaskets, screws
whose thread is coated with sealant.

Fit on the oil spray nozzles (2) and tighten the couplings (1)
to the prescribed torque.

The main bearings (1) are supplied as spare parts undersized
on the inside diameter by 0.254

÷

0.508 mm.

540811

Measuring main journal assembly
clearance

Mount the crankshaft (1).
Check the clearance between the crankshaft main journals
and their respective bearings by proceeding as follows:

-

Thoroughly clean the pins.

-

Apply a calibrated wire onto the main journals.

Not having found it necessary to replace the main
bearings, they need to be fitted back on in the same
sequence and position found upon disassembly.

Do not do any accommodating on the bearings.

Assembling main bearings

Thoroughly clean the top main bearing shells (1) and position
them in the crankcase.

The middle half ring (2) is fitted with thrust washers.

NOTE

NOTE

NOTE

236

F1C ENGINE

D

AILY

E

URO

4

Base - March 2006

Print 603.93.651

«
...
262
263
264
265
266
...
»

Summary of Contents for daily euro 4













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for daily euro 4

PLUS BLOCK AM45

Brand: A'OK Pages: 7

Brand: ebm-papst Pages: 9

Brand: MAK Pages: 2027

Brand: Flux Pages: 20

PneuTorque PTS-52-500

Brand: norbar Pages: 30

Brand: FAAC Pages: 124

Brand: Tanaka Pages: 11

Brand: Team Orion Pages: 2

Brand: Grundfos Pages: 36

Brand: dunkermotoren Pages: 30

Brand: Habasit Pages: 60

EASY-KART 100cc

Brand: IAME Pages: 35

Brand: Volvo Penta Pages: 130

Brand: Stober Pages: 48

Brand: DLE Pages: 5

Brand: Desert Aircraft Pages: 9

Brand: Desert Aircraft Pages: 11

Brand: Desert Aircraft Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands