background image

Page 2 of 6

 

GFH45-IOM Rev. 0  12/18  Printed in USA 

 

 

INSTALLATION 
 

CAUTION:

  The regulator must be installed with the 

draincock downward to allow accumulated fluid to 
drain out when the draincock is opened. 

 

CAUTION:

   Moisture and particulates can be 

discharged at high speed when draincock is 
opened.  

 
The GFH45 can be line mounted, panel mounted, or wall 
mounted (reference G6018006 wall-mount bracket).   
 
Teflon tape is the preferred thread sealant for the 1/4” 
NPT connections. 
 
Connect the supply to the port marked “IN”.  The other 
ports are outlet and factory plugged outlet gauge ports. 
 

 

 
 
WARNING

:  If the supply line is connected to the outlet 

port, regulator damage or unexpected flow through the 
regulator could occur. 

 
Prior to applying inlet pressure, double check the 
connections and assure the wrench knob or hand wheel 
is backed out sufficiently to unload the range spring in 
the bonnet. 
 
Carefully apply inlet pressure and check the supply 
connection for leakage.  Adjust the output pressure by 
rotating the wrench knob or hand wheel clockwise and 
check the outlet connection for leakage. 
 

WARNING:

 The handwheel or wrench knob can vibrate 

loose and fall out if the jam nut is not tightened. 

 

            

 

 
Figure 1 – Regulator dimensions with 1/4” NPT connections.  For certified dimensional drawing, see A17-83.

 

Summary of Contents for GFH45







Reviews: