background image

Page 4 of 6

 

GFH45-IOM Rev. 0  12/18  Printed in USA 

 

 

 

 

 

 

 
TROUBLESHOOTING GUIDE

 

 

Symptom

:  Outlet pressure continues to rise after flow 

ceases. 
 

Potential Cause

:  Valve seat leakage 

Repair

:  Disassemble and clean regulator 

components.  Install new valve plug and filter element 
(if applicable). Reassemble. 
 

Symptom

:  External leakage 

 

Potential Cause

:  Diaphragm to body joint seal 

leakage. 

Repair:

  Disassemble.  Inspect regulator body where 

diaphragm seals.  Replace diaphragm assembly. 
 

Potential Cause

:  Bowl to body joint leakage. 

Repair:

  Disassemble.  Inspect regulator body where 

bowl o-ring contacts.  Inspect bowl where o-ring 
contacts.  Replace o-ring.

  

 
 
 
 
 

 
 
 
 
 
 
Symptom

:  External leakage 

 

Potential Cause

:  Draincock leakage. 

Repair:

  Tighten draincock by turning handle 

clockwise. 

 
Symptom

:  Outlet pressure cannot be adjusted to 

maximum control range. 

Potential Causes: 

1.  Control knob positive stop adjustment. 
2.  Flow induced droop. 

Repair:   

1.  Adjust positive stop of control knob.  
2.  A higher output range regulator may be required. 
 

Symptom:

  Noisy operation. 

 

Potential Causes:

 Turbulence in adjacent piping. 

Repair: 

Insure that there are no elbows, line tees or 

other turbulence creating piping directly upstream or 
downstream of the pressure regulator. 

 
 

Summary of Contents for GFH45







Reviews: