manualshive.com logo in svg

iSys iTerra Elite, Quick Start Manual

Share
Download
iSys iTerra Elite Quick Start Manual Download Page 23

_________________________________________________________________________________________________________________________ 

PAGE 23

 --- 

iTerra Elite 

Quick Start Guide 

© 2008 iSys-The Imaging Systems Group Inc.   

 

 

I. INTERFACES 

 

Your printer is equipped with a selection of data interfaces.  See rear of Printer: 

 

                          

 

 

1. 

Parallel 

– For direct connection to a PC. This requires a bi-directional parallel port with a (IEEE 1284 compliant) 

parallel cable. 

2. 

USB 

– For connection to a PC running Windows XP or Windows 2000. This port requires a cable conforming to 

USB version 1.1 or above. 
The operation of a printer is not assured if a USB compatible device is connected concurrently with other USB-
compatible devices (USB A Male to USB B Male cable). 

3. 

Ethernet 

– For network cable connection. Optional Network card is required. 

 

NOTE: 

Administrator’s authority may be required when installing a network connection. 

Summary of Contents for iTerra Elite
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands