Isuzu AU-4LE1T Maintenance Manual Download Page 23 | Manualshive

Page: 23 / 126

background image

18

2. EC EMISSION CONTROL LABEL: ENGINE LABEL (ONLY EC TYPE)

Emission control label is attached at the front of injection pump cover located at the right side of cylinder body or the
cylinder head cover.

The following is the detail of a label required for engine emission control information, along with location.

EMISSION CONTROL INFORMATION
ISUZU MOTORS LTD. MADE IN JAPAN

ENGINE FAMILY : XXXXXXXXXX

ENGINE TYPE : XXXXXXXXXX

THIS ENGINE IS CONFORMED 97/68/EC DIRECTIVE.

ENGINE I.D.NUMBER : XXXX-XXXX

TYPE APPROVAL NUMBER : XXXXXXXXXXXXXXXXXX

XXXXXX

IMLE0106

«
...
21
22
23
24
25
...
»

Summary of Contents for AU-4LE1T































































































































Reviews:

No comments

Related manuals for AU-4LE1T

Brand: VEM Pages: 16

Brand: V2 Pages: 20

Brand: YuanDong Pages: 23

Brand: Briggs & Stratton Pages: 26

Brand: Transtecno Pages: 10

Brand: Saito Pages: 2

Brand: MJ Research Pages: 143

Brand: Bosch Pages: 106

rexroth MSK 030

Brand: Bosch Pages: 72

Rexroth MKE Series

Brand: Bosch Pages: 134

Brand: Bosch Pages: 82

Brand: Bosch Pages: 124

Rexroth MKE E Series

Brand: Bosch Pages: 138

Brand: AUSTAR Pages: 11

Brand: Leadshine Technology Pages: 11

Brand: Jets Munt Pages: 24

Brand: RADEMACHER Pages: 72

Brand: O.S. engine Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands