Isuzu AU-4LE1T Maintenance Manual Download Page 110

Page: 110 / 126

105

Symptom Cause

Action

Air mixing in injection pump.

Bleed air.

Fuel filter clogged.

Change element.

Overflow valve malfunction.

◎

Incorrect engine control adjustment.

◎

Deteriorated governor spring.

◎

Incorrect valve clearance adjustment.

Make a readjustment.

Nozzle holder misalignment.

◎

Cylinder bore wear.

◎

Air cleaner clogging.

Clean element.

Lack engine output.

Such as inferior ventilation.

Check engine condition. Ventilate and improve it.

At low speed, insufficient
torque.

EGR valve fixing. (Open position.)

◎

Wrong selection of kind of viscosity.

Change with oil of correct viscosity.

Improper oil.

Too much oil quantity.

◎

Oil coming
up.

Wrong selection of cylinder liner and piston ring.

◎

Oil coming
down.

Faulty valve stem seal.

◎

Damaged packing.

Change packing.

Improper tightening.

Retighten oil filler cap.

Excessive oil
consumption.

Oil leakage.

Improper installation of filter and piping.

Reinstall filter and piping.

Summary of Contents for AU-4LE1T































































































































Search results

Summary of Contents for AU-4LE1T

Reviews:

Related manuals for AU-4LE1T

Brands by name

Popular brands

Isuzu AU-4LE1T, Maintenance Manual

Search results

Summary of Contents for AU-4LE1T

Reviews:

Related manuals for AU-4LE1T

Brands by name

Popular brands