Isuzu AU-4LE1T Maintenance Manual Download Page 111

Page: 111 / 126

106

Symptom Cause

Action

Damaged packing.

Change packing.

Fuel leakage.

Improper installation or tightening.

Reinstall or retighten air bleeder plug.

Too much
injection
amount.

Injection pump misadjustment.

◎

Excessive
fuel
consumption.

Excessive
mechanical
loads.

Operation

Check the mechanical loads.

Clogged air cleaner.

Clean or change element.

Nozzle damage.

◎

Nozzle misadjustment.

Make a readjustment.

Injection timing failure.

◎

Injection amount misadjustment.

◎

Improper fuel.

Use fuel in this instruction manual.

Much black
smoke.

EGR valve fixing. (Open position.)

◎

Oil coming up or down.

Change oil.

Water mixing in fuel.

Remove water.

Low compression pressure.

◎

Injection timing failure.

◎

Improper
exhaust.

Much white
smoke.

Low coolant temperature.

Inspect or change thermostat.

Crack in battery body.

Change battery.

Battery
overdischarge.

Low
electrolyte
level.

Natural consumption.

Change battery.

Summary of Contents for AU-4LE1T































































































































Search results

Summary of Contents for AU-4LE1T

Reviews:

Related manuals for AU-4LE1T

Brands by name

Popular brands

Isuzu AU-4LE1T, Maintenance Manual

Search results

Summary of Contents for AU-4LE1T

Reviews:

Related manuals for AU-4LE1T

Brands by name

Popular brands