iseg NHR 20 20 Page 31 Technical Documentation Manual Download | Manualshive

Page: 31 / 31

background image

11. Warranty & Service

This device is made with high care and quality assurance methods. The standard factory warranty is 36 months. Please
contact the iseg sales department if you wish to extend the warranty.

CAUTION!

Caution!

Repair and maintenance may only be performed by trained and authorized personnel.

For repair please follow the RMA instructions on our website:

www.iseg-hv.com/en/support/rma

12. Disposal

INFORMATION

INFORMATION

All high-voltage equipment and integrated components are largely made of recyclable materials. Do not
dispose the device with regular residual waste. Please use the recycling and disposal facilities for electrical and
electronic equipment available in your country.

13. Manufacturer´s contact

iseg Spezialelektronik GmbH

Bautzner Landstr. 23
01454 Radeberg / OT Rossendorf
GERMANY
FON: +49 351 26996-0 | FAX: +49 351 26996-21

www.iseg-hv.com

[email protected]

[email protected]

NHR – NIM standard High Voltage Power Supply | Last changed on: 25.11.2019 |

www.iseg-hv.com

31/31

«
...
29
30
31

Summary of Contents for NHR 20 20
































Reviews:

No comments

Related manuals for NHR 20 20

Brand: UFO Pages: 16

Brand: Raymarine Pages: 24

Brand: Hansen Pages: 72

Brand: AAT Pages: 16

Brand: AAT Pages: 40

Platinum Series

Brand: Dairy Tech Pages: 38

Brand: H&S Pages: 34

Brand: QAL Medical Pages: 42

Brand: ParaBody Pages: 3

Brand: Valiani Pages: 66

Brand: Zero 88 Pages: 12

Brand: Zeiss Pages: 119

Brand: Zehnder Rittling Pages: 32

Brand: MAKSIWA Pages: 155

Brand: U-Line Pages: 6

Brand: GE Pages: 241

Brand: GE Pages: 223

Brand: Salvis Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands