IQ Power Tools iQTS244KIT Operator'S Manual Download

Page: 10 / 36

iQTS244

Operator’s Manual

888-274-7744

www.iqpowertools.com

gli

General

This section describes the machine

’

s safety equipment,

its purpose, and how checks and maintenance should be

carried out to ensure that it operates correctly.

WARNING!

NEVER USE A MACHINE THAT HAS

FAULTY SAFETY EQUIPMENT

BLADE GUARD

The blade guard is designed to prevent parts of

the blade or cutting fragments from being thrown

towards the user.

CHECKING THE BLADE GUARD

Check that the guard over the blade is not cracked or

damaged in any other way. Replace when damaged.

NEVER USE THE MACHINE

WITHOUT A GUARD NOR WITH A

DEFECTIVE GUARD. ALWAYS CHECK THAT THE GUARD IS

CORRECTLY FITTED BEFORE STARTING THE MACHINE.

IT IS NOT PERMITTED TO EXPOSE THE BLADE MORE THAN

180 DEGREES WITHOUT PROTECTION.

WARNING!

SHUT DOWN THE MACHINE AND

DISCONNECT THE POWER PLUG.

DUST GUARD

The dust guard is designed to prevent dust being pulled

up from the backside of the blade. The dust guard should

be inspected periodically for damage. The dust guard

should move freely sliding up and over cutting material.

MACHINE’S SAFETY EQUIPMENT

SAW POWER SWITCH

The power switch

- / O

should be used to start and stop

the machine.

CHECKING THE SAW POWER SWITCH

The saw power switch starts the saw motor and

vacuum motor simultaneously.

To start the saw motor press the

POWER

switch

on symbol. To stop the saw motor press the

POWER

switch

or off symbol.

Defective switches should be replaced by an authorized

service workshop.

VACUUM ONLY SWITCH

The vacuum only switch turns the vacuum on but not

the saw motor.

To start the vacuum motor press the

VACUUM ONLY

switch

or on symbol. To stop the vacuum motor press

the

VACUUM ONLY

switch

or off symbol.

LASER SWITCH

This tile saw is equipped with a laser light guide for

lining up cuts.

To turn on the laser light guide press the

LASER

switch

or on symbol. To turn off the laser light guide press the

LASER

switch

or off symbol.

LOCKING KNOB, ROLLING TABLE

The locking knob is used to lock the rolling table in place

when in transit. Be sure to lock rolling table before

transit to avoid injury.

4.1

Summary of Contents for Power Tools iQTS244KIT





































Search results

Summary of Contents for Power Tools iQTS244KIT

Reviews:

Related manuals for Power Tools iQTS244KIT

Brands by name

Popular brands

IQ Power Tools iQTS244KIT, Operator'S Manual

Search results

Summary of Contents for Power Tools iQTS244KIT

Reviews:

Related manuals for Power Tools iQTS244KIT

Brands by name

Popular brands