INVT MH860 Series Operation Manual Download Page 99

Page: 99 / 125

MH860 series hydraulic servo drive

Troubleshooting

8.2 Fault handling flowcharts

Err01: IPM fault

ERR01

Is the drive output loop grounded or

short circuited?

Is the motor power cable short

circuited or shorted to the ground or

thermocouple?

Remove the wiring fault.

Yes

Remove the wiring fault or

replace the motor.

Yes

Is the braking resistor output short

circuited or shorted to the housing?

Remove the wiring fault or

replace the braking

resistor.

Yes

Is the drive model displayed on the

HMI same as that on the nameplate?

Set the drive again.

Contact the local

dealer or our

technical support.

Yes

Err02: Overcurrent

ERR02

Is the motor rotation speed too low

(within ±10 rotations) according to

fault records?

Does the motor vibrate greatly during

running?

Yes

Is the drive output loop grounded or

short circuited?

Yes

Remove the wiring fault.

Remove the resolver wiring

fault and motor three-phase

output wiring fault. Re-measure

the motor initial angle after re-

wiring.

Adjust the speed/ pressure

proportional/integral gains to

make the system run smoothly.

Contact the local

dealer or our

technical support.

Summary of Contents for MH860 Series






























































































































Search results

Summary of Contents for MH860 Series

Reviews:

Related manuals for MH860 Series

Brands by name

Popular brands

INVT MH860 Series, Operation Manual

Search results

Summary of Contents for MH860 Series

Reviews:

Related manuals for MH860 Series

Brands by name

Popular brands