background image

 
 

BALNAFETTACH HOUSE, PH26 3LW             (01479) 872 518                   [email protected]

 

 

 

MicroFogger keeps charging forever (Battery Charge Indicator Does Not Increase) 

If the MF3 battery level does not increase at all even where it has been charged for several 
hours 

 first make sure the Rocker Switch has been set to the 

ON

 during charging. 

MicroFogger turns on when the USB cable is plugged into it but the other end of the cable 
is not in a charger! 

This can occur when the Charge Lock is 

OFF

.  Some charging cables make the MF3 

recognise them as a 

trigger input

 (a feature that allows the MF3 to be triggered via a 

cable).  To resolve this issue 

 turn the Charge Lock back to 

ON

Microfogger Activates Randomly While Charging 

This can happen if you are using a computer or a power bank to chanrge the MF3.  If the 
computer/power bank goes to 

sleep

 during the charging process, the MF3 may 

inadvertently recognise this as a control cable signal.  To prevent this from happening, only 
use 

wall-socket

 type USB chargers. 

MicroFogger produces a burning smell even with a new heating coil 

 

There may be a very slight burning smell present in the first few second of operation with a 
new coil.  This is normal.  If the smell persists or becomes more noticeable, stop using the 
MF3 and allow it to rest for at least another 30 minutes before switching on again.   

Ensure that the fluid tank is fully filled. In cold environments, the fog liquid becomes more 
viscous (thickens) and will take longer to be absorbed into the heating coil.  

In these situations, place the MicroFogger in a warm area before using it. 

 

Safety Considerations 

The MicroFogger 3 (MF3) is powered by a high-performance Lithium-ion battery. This type 
of battery presents a potential fire risk if handled improperly. The following safety 
guidelines aim to prevent any issues from arising: 

 

Never leave the MF3 charging while unattended 

 

Never charge an MF3 using a computer or a battery bank 

 

Keep the MF3 away from any flammable materials 

 

Do not expose the MF3 to temperatures over 40

0

 

Never attempt to disassemble the MF3 or undertake unauthorised modifications 

 

Don’t expose

 to direct sunlight for extended periods of time 

 

Always ensure the MF3

’s heating coil compartment is clear of debris

 

 

If the MF3 sustains a significant impact through a drop or other mishap, immediately 
cease operation (unplug it if it is charging) and place it in a safe area 
outdoors and wait for at least 10 minutes.  

Summary of Contents for MicroFogger 3 Pro














Reviews: