background image

 
 

BALNAFETTACH HOUSE, PH26 3LW             (01479) 872 518                   [email protected]

 

 

 

 

 

 

 

 

Power Adjustment Menu  

After entering this interface by pressing the menu button, you’ll be able 

to adjust the 

density of the smoke produced (coil power) by pressing the select button.  

Every time you press the select button, the power level will be increased by one bar until all 
8 bars are filled at which point it will loop back to 1 bar.  

More bars equals to a higher power level.  

Once the desired density is achieved, mode can be pressed again to begin adjusting the 
speed of the smoke (fan power level) in the same way as detailed above.  

Throughout this process, you can hold the trigger button to see how changes to these 
settings impact the smoke production in real-time.  

To return back to the home screen, simply don’t press the mode or select buttons for 2 

seconds. 

Advanced Settings Menu  

This interface can be entered by holding the mode button for 4 seconds while you are on 
the home screen.  

Once you’ve entered, the 

Mode button (lower) will cycle the setting that you are adjusting 

and Select (upper) will cycle through the different options the setting can be adjusted to. 
Here is a visual representation of the menu: 

 

 

 

 

 

 

 

 
 
 

Summary of Contents for MicroFogger 3 Pro














Reviews: