background image

 
 

BALNAFETTACH HOUSE, PH26 3LW             (01479) 872 518                   [email protected]

 

 

 

 

 

 

 

 

 

 

 

Pin 5 = +ve

 

 

 

Pin 4 = data 

 

Pin 3 = data 

 

Pin 2 = unused 

 

Pin 1 = -ve 

 

 

Support and FAQs 

Can the MicroFogger trigger smoke alarms? 

Yes!

  Ionization and photoelectric smoke alarms may be activated. Traditional heat-

activated smoke alarms and sprinklers will not be affected. 

Is it possible to change the smoke colour? 

Unfortunately, not. The MF3 produces smoke by heat evaporation of a fog liquid.  It can 
only be white and adding a dye to the liquid will not change the smoke colour.  

The only way to simulate coloured smoke using the MF3 would be to use external lighting 
(eg lasers). 

Can I breathe in the smoke? 

The liquid is a food additive and under normal operations, the fog produced is considered to 
be non-toxic.  However, we do not recommend breathing in the smoke.  

The smoke can only become potentially harmful to inhale if the safety precautions regarding 
the replacement of worn-out heating coils are not followed 

What is the fog liquid? 

The liquid consists of a high purity vegetable glycerine and propylene glycol mixture and is 
sometimes used as a food additive. The same liquid is also found in cigarette replacement 
vaping units. 

Can I use liquids from other smoke machines? 

Liquids from other fog machines are usually far less viscous (thinner) than our composition 
so if used in the MicroFogger, they are unlikely to produce any smoke.  

We can only guarantee the safety and performance of the fog liquid that we sell so if you 
decide to experiment with other compositions, this would at your own risk. 

Summary of Contents for MicroFogger 3 Pro














Reviews: