background image

 

 

1. Precaution 

1.1 Safety Precaution 

 

To prevent injury to the user or other 

people and property damage, the following 

instructions must be followed. 

 

Incorrect operation due to ignoring 

instruction will cause harm or damage.   

 

Before service the unit, be sure to 

read this service manual at first. 

 

1.2 Warning 

 

Installation 

 

Do not use a defective or underrated 

circuit breaker. Use this appliance on a 

dedicated circuit. 

There is risk of fire or electric shock. 

 

For electrical work, contact the dealer, 

seller, a qualified electrician, or an 

authorized service center. 

Do not disassemble or repair the product, 

there is risk of fire or electric shock. 

 

Always ground the product. 

There is risk of fire or electric shock. 

 

Install the panel and the cover of 

control box securely. 

There is risk of fire of electric shock. 

 

Always install a dedicated circuit and 

breaker. 

Improper wiring or installation may cause fore 

or electric shock. 

 

Use the correctly rated breaker of 

fuse. 

There is risk of fire or electric shock. 

 

Do not modify or extend the power 

cable. 

There is risk of fire or electric shock. 

 

Do not install, remove, or reinstall the 

unit by yourself (customer). 

There is risk of fire, electric shock, explosion, 

or injury. 

 

Be caution when unpacking and 

installing the product. 

Sharp edges could cause injury, be especially 

careful of the case edges and the fins on the 

condenser and evaporator. 

 

For installation, always contact the 

dealer or an authorized service center. 

 

Do not install the product on a 

defective installation stand. 

 

Be sure the installation area does not 

deteriorate with age. 

If the base collapses, the air conditioner could 

fall with it, causing property damage, product 

failure, and personal injury. 

 

Do not let the air conditioner run for a 

long time when the humidity is very high 

and a door or a window is left open. 

 

Take care to ensure that power cable 

could not be pulled out or damaged during 

operation. 

There is risk of fire or electric shock. 

 

Do not place anything on the power 

cable. 

There is risk of fire or electric shock. 

 

Do not plug or unplug the power 

supply plug during operation. 

There is risk of fire or electric shock. 

 

Do not touch (operation) the product 

with wet hands. 

 

Do not place a heater or other 

appliance near the power cable. 

There is risk of fire and electric shock. 

 

Do not allow water to run into 

electrical parts. 

It may cause fire, failure of the product, or 

electric shock. 

 

Do not store or use flammable gas or 

combustible near the product. 

There is risk of fire or failure of product. 

 

Do not use the product in a tightly 

closed space for a long time. 

Oxygen deficiency could occur. 

 

When flammable gas leaks, turn off 

the gas and open a window for ventilation 

before turn the product on. 

 

If strange sounds or smoke comes 

from product, turn the breaker off or 

Summary of Contents for P7MVI-09WiFi

































































Reviews: