background image

42 

8.5 Multi-function board instruction (This multi-function board is optional) 

8.5.1. Function 

The  multi-function  board  receives  the  signal  of  4-cored  wired  controller(central  controller),Non-polar 

wired  controller  and  CP  remote  on-off  signal(  ON-OFF  command  signal)  .  Then  converting  it  to  the 

communication signal to the main control board.   

The multi-function board can output Alarm signal. 

The multi-function board has two versions, one for Non-polar wired controller, the other one for 4-cored 

wired controller or central controller. 

8.5.2. CP remote on-off 

8.5.2.1  For  CP  command,  closed  indicate  the  remote  on-off  control  signal  OFF,  Disconnected 

indicate    the remote on-off control signal    ON. It needs 3 seconds to determine on/off status. 

CP command will be delivered one time immediately after power on. 

8.5.2.2 Dip-switch F2 setting status are as below: 

Dip-switch 2 

Dip-switch 1 

Remote on-off control status 

OFF 

OFF 

Disconnected send CP, closed cancel CP 

ON 

OFF 

Closed send CP, disconnected cancel CP 

8.5.3. ON-OFF control 

8.5.3.1  It  needs  3  seconds  to  determine  on/off  status.

  ON-OFF

  command  do  not  be  delivered  after 

power on, only when the status changed, It can send the command. 

8.5.3.2  When  ON-OFF  control  disconnected,  it  will  send  switch-on  signal:  the  unit  will  run  in  Auto 

mode  ,Auto  fan  speed,  24

  setting  temp.  When  ON-OFF  control  closed,  it  will  send  switch-off 

signal. 

8.5.3.3 Dip-switch F2 setting status are as below: 

Dip-switch 2 

Dip-switch 1 

Remote on-off control status 

OFF 

ON 

Disconnected send ON, closed send OFF 

ON 

ON 

Closed send OFF

disconnected send ON 

8.5.4. 4-cored wired controller

Central controller and Non-polar wired controller 

Note: 4-cored wired controller

Central controller and Non-polar wired controller 

are mutually exclusive. They can only be chosen one of three at the same time. 

8.5.4.1    For network address, Dip-switch F1 and Rotary switch ENC3 are set as below: 

Dip-switch 2 

Dip-switch 1 

Based address 

OFF 

OFF 

OFF 

ON 

16 

ON 

OFF 

32 

ON 

ON 

48 

Summary of Contents for P7MVI-09WiFi

































































Reviews: