Invenco G6 OPT 6500x Installation Manual Download Page 28 | Manualshive

Page: 28 / 40

background image

Invenco Group Limited Proprietary & Confidential

6.4.1.2 Card-Reader Slot

Visual inspection of the G6OPT for ICC bugs can be performed by comparing the following photo’s
of the G6OPT card-reader slot to the G6OPT being inspected.

The following aspects must be considered during this inspection:



There must not be any wires of any kind originating from the ICC slot.



The OPT finish must be uninterrupted and consistent across the card acceptor aperture.



The card acceptor illuminator must turn on and off when a card reader is ready to accept a
card.

Front of Card Slot

Card Insertion Illuminator

«
...
26
27
28
29
30
...
»

Summary of Contents for G6 OPT 6500x









































Reviews:

No comments

Related manuals for G6 OPT 6500x

Brand: EBN Technology Pages: 14

TASHI MT38NOREADER01

Brand: Unitech Pages: 39

Brand: EC Line Pages: 20

Brand: LUNU Pages: 35

Brand: Toshiba Pages: 6

TEC POS ST-5600 Series

Brand: Toshiba Pages: 22

TFTST-76T-5A SERIES

Brand: Toshiba Pages: 24

Brand: Toshiba Pages: 126

Neon 2000 Series

Brand: UniData Communication Systems Pages: 59

RemoteSAT RST100B

Brand: Beam Pages: 40

CPX-AB-2-M12-RK-IB

Brand: Festo Pages: 2

CPV ASI-4E3A-Z Series

Brand: Festo Pages: 14

Compact Performance CPV GE-IP-8 Series

Brand: Festo Pages: 50

CPV GEASI-4E4A Series

Brand: Festo Pages: 74

VTSA-ASI 4E4A-Z Series

Brand: Festo Pages: 86

IIFB11-02 Series

Brand: Festo Pages: 210

Brand: DIEBOLD NIXDORF Pages: 109

Brand: Pax Technology Pages: 151

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands