Intellijel MIDI 1U Manual Download Page 13

 
 

[2] LEARN  

  button   -   Use   this   button   to   learn  

which   MIDI   channel   the   MIDI 1U   will  
respond   to,   as   well   as   the   MIDI   CC  
numbers   assigned   to   both   the    

CC  

[G]  

  and  

MOD  

[D]  

  output   jacks.  

MIDI 1U   automatically   saves   all   learned  
settings   (both   buttons   flash    

green 

)   after  

2 seconds   of   MIDI   inactivity,   ensuring   it  
returns   to   exactly   the   same   state   after   a  
power   cycle.  

Pressing   the   button   cycles   through   three   states:  

OFF  

  :   When   the   LEARN   button   is   off,   MIDI 1U   is   in   normal   operation   and   works   to   convert  

incoming   MIDI   data   into   CV   for   your   eurorack   system.  

SOLID   BLUE  

  :   Indicates   the   MIDI 1U   is   in    

LEARN   CC+CH   mode 

,   meaning   the   module   is  

awaiting   a   MIDI   message,   and   that   it   will   use   the   first   message   it   receives   to   set   both   the  
module’s   MIDI   Receive   channel   and    

CC  

[G]  

  jack   assignment.   In   addition,   it   will   set   the  

CC 

 jack’s   polarity   based   on   the   status   of   the    

CLK  

÷  

  button,   as   discussed   earlier.  

FLASHING   BLUE  

  :   Indicates   the   MIDI 1U   is   in    

LEARN MOD+CH   mode 

,   meaning   the  

module   is   awaiting   a   MIDI   message,   and   that   it   will   use   the   first   message   it   receives   to   set  
both   the   module’s   MIDI   Receive   channel   and    

MOD  

[D]  

  jack   assignment.   In   addition,   it   will  

set   the    

MOD 

 jack’s   polarity   based   on   the   status   of   the    

CLK  

÷  

  button,   as   discussed   earlier.  

For   more   information   about   using   the    

LEARN  

  button,   see    

Configuring   MIDI   1U   Using   the   Front  

Panel 

,   later   in   this   manual.  

Alternatively,   you   can   set   the   MIDI   channel,    

MOD  

  and    

CC  

  jack   assignments   using   the    

Intellijel  

Config  

  app,   discussed   later.  

DUAL   MODE:   MIDI   1U   offers   an   alternate,   dual   channel   mode   that   reconfigures   the   jacks   for  
2-channel   operation.   In   this   mode,   you   have   independent   MIDI   control   of   the   pitch,   gate   and  
velocity   for   two   different   MIDI   channels.   See    

Dual   Mode  

  for   detailed   information   about   enabling  

the   mode,   and   using   the   LEARN   button   within   it.  

Outputs  

[A] CLK  

  out   -   Clock   output,   which   transmits   a   divided   MIDI   clock   pulse   with   a   division   set   by   the  

CLK  

±    

 [1]  

  button.   The   corresponding   LED   blinks   in   time   with   the    

CLK  

  out.  

Alternatively,   you   can   use   the    

Intellijel   Config  

  app   to   set   the   desired   Clock   Division.  

[B] RST  

  out   -   Operates   as   either   a   RESET   output   or   a   RUN   output,   depending   on   how   it’s  

configured   inthe    

Intellijel   Config  

  app.  

 

MIDI   1U   System   Manual 

12  

Summary of Contents for MIDI 1U





























Reviews: