Intellihot iN401 Operation & Installation Manual Download

Page: 8 / 80

iN401 - iN501 Safety

May

2019

Revision

CAUTION

Make sure you know the location of the gas shut-off

valve and how to operate it. Immediately close the

gas shut-off valve if the water heater is subjected to

fire, overheating, flood, physical damage, or any other

damaging condition that might affect the operation of

the unit. Have the water heater checked by a qualified

technician before resuming operation.

If the water quality is known to have high acidity and/

or high hardness, water treatment is recommended.

Consult the local water authority.

SAFETY

INSTRUCTIONS

DO NOT use this appliance if any part has been under

water.

DO NOT reverse the cold water and gas connections as

this will damage the gas valve.

DO NOT overtighten fittings as damage may occur,

causing internal leakage.

The appliance should be located in an area where leakage

within the unit or at its connections will not result in

damage to the surrounding area. The manufacturer

will not be responsible for any damage resulting from

leaking if adequate drainage is not provided.

Summary of Contents for iN401

















































































Search results

Summary of Contents for iN401

Reviews:

Related manuals for iN401

Brands by name

Popular brands

Intellihot iN401, Operation & Installation Manual

Search results

Summary of Contents for iN401

Reviews:

Related manuals for iN401

Brands by name

Popular brands