manualshive.com logo in svg

Intellihot iN401, Operation & Installation Manual

Share
Download
Intellihot iN401 Operation & Installation Manual Download Page 20

iN401 - iN501 Gas

 

Connection

16

May

 

2019

 

-

 

Revision

 00 

6. Local codes may require multiple units to have a shut-off

valve on the main gas supply line and one on each unit.

6.9  Connecting Gas Line to Unit

Note

:

  

Always clean the inside of the gas line of any dirt or 

debris before connecting the piping to the unit.

Main Supply

Line

Drip

Leg

Manual

Shut-off

Valve

Main Supply 

Line

Drip

Leg

Drip

Leg

Drip

Leg

Drip

Leg

Manual

Shut-off

Valve

Manual

Shut-off

Valve

Manual

Shut-off

Valve

Manual

Shut-off

Valve

1. Install a 4-5/8” OD flanged steel coupling and gasket with

a short piece of 1-1/4” NPT black pipe.

2. Install a manual shut-off valve as described in “6.8 Gas

Pipe Drip Leg and Shut-off Valve” on page 15

Union

Shut-off

Valve

3. Install a drip leg in “6.8 Gas Pipe Drip Leg and Shut-off

Valve” on page 15.

4. Continue installing pipe to reach the main gas supply

connection.

5. Test all gas pipe connections.

a. All the gas pipe connections should be tested as

prescribed in NFPA 54.

b. In multiple unit applications, each unit should be

isolated before testing any piping system may exceed

the allowable pressure of 14.0” W.C..

NOTICE

Do not fire (operate) the water heater until all connections 

have been completed and the heat engine is filled with 

water.

Summary of Contents for iN401

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands