Intellihot iN401 Operation & Installation Manual Download Page 41

Page: 41 / 80

iN401 - iN501 Operation

May

2019

Revision

12. Operation

12.1 Control Panel

Main Menu Screen

Selecting the Menu button brings up this screen.

A sleep mode screen will appear after a period of inactivity.

12.2 Turning Water Heater ON and OFF

1. When power is applied to the water heater or the

electrical switch is turned ON, the Main Menu screen will

automatically appear.

2. To turn the water heater OFF, press and hold the Power

button in the upper left of the screen.

3. Press the Power button to turn the unit ON.

WARNING

Turning the unit OFF does not disconnect it from the

power source. Whenever working around electrical

components within the water heater, turn off the power

at its source. Touching live electrical components can

cause serious injury or death.

Summary of Contents for iN401

















































































Search results

Summary of Contents for iN401

Reviews:

Brands by name

Popular brands

Intellihot iN401, Operation & Installation Manual

Search results

Summary of Contents for iN401

Reviews:

Brands by name

Popular brands