Intellihot iN401 Operation & Installation Manual Download Page 62

Page: 62 / 80

iN401 - iN501 Wiring Diagrams and Troubleshooting

May

2019

Revision

Description

Possible

Cause

Remedy

Software

• Incorrect settings.
• Incompatible settings.
• Incorrect software version.
• Faulty wiring.

• Review and correct settings.
• Review and correct settings.
• Update software version.
• Check for nicked or broken sensor wiring or connectors. Also

check for corroded or wet connectors.

Manifold Sensors

• Unplugged connectors.

• Faulty sensor wiring.

• Faulty sensor.

• Flue temperature sensor.
• Inlet water temperature sensor.
• Faulty controller.

• Check connectors and ensure they are securely connected

• Check for nicked or broken sensor wiring or connectors. Also

check for corroded or wet connectors

• Measure resistance of sensor at connector (18 kΩ at 50°F,

10 kΩ at 77°F, 3 kΩ at 140°F)

• Replace controller.

System Alert / Fault

• A system alert or fault is present

(main menu screen).

• Malfunction of monitored part or

system.

• Press the Menu bar and refer to the remedy for indicated

part or system.

Summary of Contents for iN401

















































































Search results

Summary of Contents for iN401

Reviews:

Brands by name

Popular brands

Intellihot iN401, Operation & Installation Manual

Search results

Summary of Contents for iN401

Reviews:

Brands by name

Popular brands