Intellihot iN401 Operation & Installation Manual Download Page 52

Page: 52 / 80

iN401 - iN501 Connecting

Multiple

Units

May

2019

Revision

13. Connecting Multiple Units

13.1 General Information

Multiple units can be connected together to supply large

demands of hot water.

The water heaters communicate through a cable connection

between each water heater. The benefits of connecting the

units are:

• When demand for hot water is low, fewer units will operate.

• If one unit has an error code, the others will continue to

operate.

• Changing the settings (temperature, time, etc.) on one unit

changes settings on all the units.

• It allows shut down of one unit for maintenance while the

others continue to operate.

13.2 Installation Procedure

1. Connect all the units to a gas supply pipe. Make sure the

pipe is properly sized in accordance with the BTU draw

and number of units being operated. Refer to “6. Gas

Connection” on page 14 for additional information.

2. Connect all the units to the power supply. Refer to “9.

Electrical Power” on page 31 for additional information.

Main Supply

Line

Drip

Leg

Drip

Leg

Drip

Leg

Drip

Leg

Manual

Shut-off

Valve

Manual

Shut-off

Valve

Manual

Shut-off

Valve

Manual

Shut-off

Valve

3. Install the combustion (fresh) air intake and exhaust

outlet pipes. Refer to “7. Air Intake Inlet and Exhaust Gas

Outlet Pipe Connections” on page 19 for additional

information.

4. Install and connect the hot water lines. If an optional hot

water storage tank is required, connect the hot water

lines to this tank. Make sure the water pipe is properly

sized in accordance with the number of units being

operated.

5. Install and connect the cold water lines. Make sure the

water line is properly sized in accordance with the number

of units being operated.

6. Connect and route the condensate drain lines to a suitable

discharge location. Refer to “8. Water Connections” on

page 28 for additional information.

7. Do Not

connect communication cables at this time.

8. Power up all the units and assign a unique number, one

through four to each unit. Set the STAGING to ON.

WARNING

Before making any adjustments or connections inside

the water heater cabinet, make sure the power is

disconnected. Unplug the water and/or turn the circuit

breaker OFF.

9. If necessary, press the Power button to turn OFF each

water heater in the system and disconnect power from all

the units in the system.

NOTE: It is necessary to wait a minimum of 30 seconds

here

Summary of Contents for iN401

















































































Search results

Summary of Contents for iN401

Reviews:

Brands by name

Popular brands

Intellihot iN401, Operation & Installation Manual

Search results

Summary of Contents for iN401

Reviews:

Brands by name

Popular brands