Intellihot iN401 Operation & Installation Manual Download Page 26

Page: 26 / 80

iN401 - iN501 Air

Intake

Inlet

and

Exhaust

Gas

Outlet

Pipe

Connections

May

2019

Revision

7.3.4 Roof Air Intake Inlet and Exhaust Gas Outlet

Pipe Termination

Venting the unit through the roof is also an option. With this

installation method, the terminations must extend at least 12”

over maximum potential snow levels, or as required by local

building codes. In areas of high snow fall, protect the vent

terminations from blockage.

Terminate the air intake inlet pipe with a 90° elbow (angled

down). A suitable roof flashing and vent cap (not supplied)

should be installed.

12” USA or

18” Canada

over maximum

snow level or

as required by

local code

12” Minimum

3’ Minimum

12” USA or

18” Canada

over maximum

snow level or as

required by local

code

Exhaust

Intake Air

Single unit.

Intake Air

Exhaust

See

Note A

Multiple units.

Note A:

The distance between any exhaust gas outlet and

air intake inlet pipe should be between 18 and 36

inches apart. If this minimum specification cannot

be met, the air intake inlet and exhaust gas outlet

pipes should be 72 inches apart or more.

7.4 Single Pipe Venting System (Power Vent)

7.4.1 Single Unit

The following illustrations represent some typical power

venting configurations and are included to assist in designing

the vent system. Possible configurations are not limited to

these designs.

Intake

Air

Intake

Air

Intake

Air

Intake

Air

Intake

Air

Intake

Air

Intake

Air

Exhaust

Summary of Contents for iN401

















































































Search results

Summary of Contents for iN401

Reviews:

Brands by name

Popular brands

Intellihot iN401, Operation & Installation Manual

Search results

Summary of Contents for iN401

Reviews:

Brands by name

Popular brands