background image

COM Port Settings

Communication port settings can  be changed and are set at the factory as:

Baud rate 19200, No Parity, 1 Stop bit, 8 Data bits.

Device Addresses

There are total of 256 available addresses in range 00-FF (Hexadecimal). All addresses are operational, but it is advised not to use
the factory default address 0x00 and the special device error address - 0xFF. The present address displyed on a 7 segment dual led
display.

Introduction

IA-3126-2

Specifications subject to change without notice.

16 Relays
16-ch Wide-Range inputs
IA Daisy-chain Series

Intelligent Appliance

The IA-3126-2 is an indutrial intelligent 16-ch Relay Control Board, with 16-ch Digital Input and multi-drop operation

capability, in the original IA-3131 foot print.

The IA-3126-2 is an Industrial grade relay controller, easy operated, supported by a simple, yet, powerful command set.

Rich software support, including open source code samples and setting utility makes it fast and easy adaptable device.

The IA-3126S is an inductive load supporting version of the original IA-3126 Controller, that includ voltage suppressors

across its Relay contacts. This version is limited to 56VDC and 40VAC load voltage operation range.

4

# 1

# 2

# 3

# 256

www.intelligent-appliance.com

Summary of Contents for IA Daisy-chain Series


























Reviews: