Intelligen INS-1500 Page 39 Installation, Operation And Instruction Manual Download | Manualshive

Page: 39 / 57

background image

39

INS-1500 & INS-2000 • 5403646 • REV F • 04/19

Trouble Alert #5 - Excessive Membrane Cycling

Trouble Alert #6 - Nitrogen Generator Cannot Keep Up While in Nitrogen Generating Mode

Trouble Alert #7 - Excess Nitrogen Demand (Sprinkler System Leak Rate Excessive)

Trouble Alert #9 - Maintenance

Trouble Alert #10 - Hardware Failure Detected

Trouble Alert #11 - PLINK Connection Error

Issue:

Nitrogen valves turn ON 16 (INS-1500) or 24 (INS-2000) times in 4 hours.

Probable Cause:

1.  Leak on sprinkler system.
2.  Leak on nitrogen tank.
3.  Pressure settings need to be adjusted or pressure transducer replaced.
4.  Membrane Outlet N

2

Solenoid (XV02) is stuck open.

Issue:

Bypass Solenoid cycles 16 times over 4 hours.

Probable Cause:

1.  Filling multiple sprinkler systems.
2.  Performing functionality testing on the nitrogen generator.
3.  Leak on nitrogen generator or sprinkler system.

Issue:

Sprinkler system leak rate is greater than Leak Rate Warning Set Point and has not been acknowledged for a week.

Probable Cause:

1.  Leak on sprinkler system.
2.  Leak on nitrogen tank.
3.  Leak Rate Warning Set Point not appropriate for application.

Issue:

Compressor Maintenance Timer expires when maintenance request has not been reset in 250 hours.

Probable Cause:

1. Standard maintenance was not completed.
2. Maintenance timer not reset.

Issue:

IntelliGen

™

Controller failure detected.

Probable Cause:

1. Short circuit on output wiring.

Issue:

Devices cannot communicate.

Probable Cause:

1. Wiring not correct.
2. Power failure.

Trouble Alert #8 - Max. Temperature Limit Reached

Issue:

Internal cabinet temperature reached max. limit.

Probable Cause:

1. Cooling fan failure.

«
...
37
38
39
40
41
...
»

Summary of Contents for INS-1500


























































Reviews:

No comments

Related manuals for INS-1500

Brand: Power Stroke Pages: 48

Brand: NuTone Pages: 28

Brand: VICI DBS Pages: 41

Lightolier HC Series

Brand: Philips Pages: 2

FULLPOWER 65213

Brand: Hyundai Pages: 40

Brand: A2Z Ozone Pages: 14

Brand: Chicago Electric Pages: 13

Powermate Ultra PM0421100 Insert

Brand: Coleman Pages: 8

Powermate PM0525312

Brand: Coleman Pages: 8

Powermate PM0543002

Brand: Coleman Pages: 12

Brand: UST Pages: 26

Brand: Chicago Electric Pages: 25

Redi-Line DA12A

Brand: Pacific Scientific Pages: 97

Brand: EINHELL Pages: 162

Brand: Scientific Pages: 20

Brand: Kanwod Pages: 21

Brand: Baldor Pages: 26

AGT 6000 PVMV-N

Brand: Fischer Panda Pages: 132

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands