Intelligen INS-1500 Page 43 Installation, Operation And Instruction Manual Download | Manualshive

Page: 43 / 57

background image

43

INS-1500 & INS-2000 • 5403646 • REV F • 04/19

1. Press "Enter" on the IntelliGen

™

Display keypad.

2.  Select "Settings" using the keypad.
3.  Enter passcode "0000".
4.  Select "Leak Rate". Press "ENTER".
5.  Press "ENTER" to choose settings.
6.  Select "Leak Rate Warning". Press "ENTER".
7.  Using the directional arrows, adjust the leak rate limit number "--" PSI per 24 hours.

a. NFPA allows 1.5 PSI per 24 hours on new systems.

b. Potter Nitrogen Generators are designed of 6 PSI per 24 hours.

8.

Press "ENTER" to confirm.

9.  Press "ENTER" to acknowledge warning.
10.  Press "ENTER" to accept change.
11.  Press "ESC" until returned to main menu.

The Leak Rate is also calculated based on the size of the sprinkler system the nitrogen generator is protecting. The INS-1500 is

factory set at 6,200 gallons (max) and the INS-2000 is factory set at 12,000 gallons (max). This can be adjusted lower if the units

are servicing smaller systems.

1. Press "ENTER" on the IntelliGen

™

Display keypad.

2.  Select "Settings" using the keypad. Press "ENTER".
3.  Enter passcode "0000".
4.  Select "Leak Rate". Press "ENTER".
5.  Press "Enter" to choose settings.
6.  Select "Sprinkler Capacity". Press "ENTER".
7.  Using the numeric pad, enter the total system volume size in gallons.
8.  Press "ENTER".
9.  Press "ESC" to return to main menu.

To Change the Leak Rate Warning Set Point:

To Change the Sprinkler System Size:

«
...
41
42
43
44
45
...
»

Summary of Contents for INS-1500


























































Reviews:

No comments

Related manuals for INS-1500

Brand: 3B SCIENTIFIC PHYSICS Pages: 5

Health Care Nano-Bubble

Brand: Humana Pages: 20

Brand: MULTIQUIP Pages: 88

Brand: Champion Power Equipment Pages: 29

Brand: Vitals Pages: 59

Brand: North Star Pages: 11

Brand: Bluetti Pages: 17

Brand: FeelTech Pages: 20

Brand: FeelElec Pages: 47

Brand: ITW GSE Pages: 126

Brand: GE Energy Pages: 2

Brand: Robin America Pages: 78

Brand: TOOLCRAFT Pages: 60

Brand: Briggs & Stratton Pages: 76

Brand: Fat Cat Pages: 10

Brand: Aremeca Pages: 20

Brand: EINHELL Pages: 24

Brand: EINHELL Pages: 173

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands