Intelligen INS-1500 Page 12 Installation, Operation And Instruction Manual Download

Page: 12 / 57

INS-1500 & INS-2000 • 5403646 • REV F • 04/19

1. On arrival, do a full inspection by checking all packages and crates in the shipment for damage.
2.

If damage is found, sign for the damage or refuse the shipment. Contact the carrier immediately and file a shipping damage

claim with the carrier.

3. Check to ensure all components are contained and no visible damage has occurred during shipping.

•

Nitrogen Cabinet

•

IntelliGen

™

Display

•

Tank Mounted Air Compressor

•

Nitrogen Tank

4. Each nitrogen generator requires a minimum of one Nitrogen Air Maintenance Device (NAMD) and one Nitrogen Purge

Valve per sprinkler system. Check to see these components have arrived.

•

Nitrogen Air Maintenance Device (one per riser) (NAMD #1119660)

•

Nitrogen Purge Valve (NGP-SPV #1119784) or (INS-PV #1119478)

•

Portable Nitrogen Analyzer (one per job) (PNA #1119504)

5. Find a location for the nitrogen generator to be installed meeting these requirements:

•

Dry, clean and well-ventilated

•

Dimensions 70” X 31” X 13” (H x W x D) for cabinet, 53” X 20” (H x W) for nitrogen tank and 74” X 37” X 24" (H x

W x D) for tank mounted air compressor.

•

Ambient temperatures above 50º F at all times

•

Access to front for service

• Conveniently located near fire sprinkler system connections

•

Conveniently located near a drain

•

Near a dedicated electrical circuit with an electrical disconnect switch

Installation of the Nitrogen Generator

Fig. 6

6. Typical installation layout of the INS-1500/2000. See Fig. 6.

7.5HP AIR COMPRESSOR

IntelliGen DISPLAY

MAIN POWER OFF/ON

1/2" OR 3/4" ELECTRICAL

CONDUIT CONNECTION

1/2" KNOCKOUT FOR

P-LINK AND NETWORK

CABLE CONNECTION

NITROGEN AIR

MAINTENENCE DEVICE

60 GALLON

NITROGEN STORAGE TANK

DRAIN CONNECTION

PIPE TO FLOOR DRAIN USING PROVIDED

3/8" OD X 10' PUSH TO CONNECT TUBE

12" LONG FLEXIBLE

STAINLESS STEEL HOSE

1/2" MNPT COMPRESSED AIR

OUTLET CONNECTION

DRAIN CONNECTION

PIPE TO FLOOR DRAIN USING PROVIDED

1/4" OD X 10' PUSH TO CONNECT TUBE

Summary of Contents for INS-1500


























































Search results

Summary of Contents for INS-1500

Reviews:

Related manuals for INS-1500

Brands by name

Popular brands

Intelligen INS-1500, Installation, Operation And Instruction Manual

Search results

Summary of Contents for INS-1500

Reviews:

Related manuals for INS-1500

Brands by name

Popular brands