Intelligen INS-1500 Page 21 Installation, Operation And Instruction Manual Download | Manualshive

Page: 21 / 57

background image

21

INS-1500 & INS-2000 • 5403646 • REV F • 04/19

8.  The amber LED labeled "BYPASS" will activate if the pressure is less than 55 PSI in the nitrogen tank.
9.  Turn power ON to the air compressor using the customer supplied electrical disconnect.
10.  The air compressor will begin running and the pressure in the air tank and nitrogen tank will begin to rise. Start recording the

time it takes until the compressor turns off.

11.  Once the nitrogen tank pressure reaches approximately 80 PSI the valves inside the cabinet will close.
12.  Once the air tank pressure reaches approximately 175 PSI the air compressor will turn off.
13.  If the nitrogen generator is isolated from the sprinkler system:

•

The air compressor of the INS-1500 and INS-2000 should take no longer than 10 minutes to pressure both tanks and turn

off.

•

If the air compressor is not turning off, or it is taking longer than expected, go to the Troubleshooting section in this

manual on page 40.

14. Once the two tanks are pressurized, the amber LED labeled "BYPASS" on the IntelliGen

™

Display will turn off and "Mode"

on the IntelliGen

™

Display will change to "N2

Mode". This indicates that the unit is now in Nitrogen Generating Mode.

15.

Check all piping connections for leaks as pre-plumbed fittings may have loosened during shipment. Any pressure drop on the

tanks during this time could indicate a leak.

«
...
19
20
21
22
23
...
»

Summary of Contents for INS-1500


























































Reviews:

No comments

Related manuals for INS-1500

Brand: Wacker Neuson Pages: 36

Brand: Wacker Neuson Pages: 58

Brand: Wacker Neuson Pages: 84

Brand: Wacker Neuson Pages: 40

Brand: NANO Pages: 28

Brand: Champion Pages: 34

POF GB/UAE 1xPPR

Brand: Datalight Pages: 2

Brand: MULTIQUIP Pages: 4

Brand: Valleylab Pages: 82

Brand: Tesla Pages: 40

Brand: TESI Pages: 66

Brand: Volker Pages: 17

Brand: Rainier Pages: 2

Brand: Shindaiwa Pages: 54

Brand: Intelligent Energy Pages: 15

Brand: Guardian Pages: 4

Brand: Guardian Pages: 22

Smart Generator

Brand: EcoFlow Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands