Intellian i4 Inland Installation And Operation User Manual Download

Page: 60 / 63

Intellian Satellite TV Antenna Systems

1. Refer to the drawing on the right.

2. Rotate antenna left and right slowly until the limit switch is pressed.

3. Turn the antenna by 360° to the reverse direction.

4. Insert the restraint foam to secure the pedestal in position with the bottom
radome.

5. Cover upper part of radome. Be careful not to touch the reflector
when assembling upper part of radome.

6. Pack Intellian i4 Inland into the original package box.

NOTE :

Don’t rotate it quickly, or you may damage the antenna limit system.

Preparation for Transportation

This is to describe how to prepare the antenna internally for transportation.
The following procedures to secure the antenna shall be strictly observed to protect it from being damaged during transportation.

Figure 34 : Preparation for Transportation

Shipping Foam

Summary of Contents for i4 Inland
































































Search results

Summary of Contents for i4 Inland

Reviews:

Related manuals for i4 Inland

Brands by name

Popular brands

Intellian i4 Inland, Installation And Operation User Manual

Search results

Summary of Contents for i4 Inland

Reviews:

Related manuals for i4 Inland

Brands by name

Popular brands