manualshive.com logo in svg

Intellian i4 Inland, Installation And Operation User Manual

Share
Download
Intellian i4 Inland Installation And Operation User Manual Download Page 28

28

Intellian Satellite TV Antenna Systems

Setting the Satellite Pair

You can change the satellite pair if you decide to receive satellite 
television service from a different service provider.

1. Press YES to enter setup mode.

2. Press YES to set satellite pair. 

3. Press YES to set triple satellites. 

SETUP MODE ?

SET SAT PAIR ?

  SET TRIPLE SAT ?

YES

PREV

YES

NEXT

NO

YES

5. Set satellite B
    Press PREV to show previous satellite name.
    Press SELECT to set chosen satellite to SAT B.
    Press NEXT to show next satellite name.

6. Set satellite C
    Press PREV to show previous satellite name.
    Press SELECT to set chosen satellite to SAT C.
    Press NEXT to show next satellite name.

7. Press YES to save selections.
      Press NO to cancel and return to main setup 

mode.

   SAT B : DTV119 

  SAT C : DTV110#

SAVE ?

PREV

PREV

YES

NEXT

NO

SELECT

4. Set satellite A
    Press PREV to show previous satellite name.
    Press SELECT to set chosen satellite to SAT A.
    Press NEXT to show next satellite name.

   SAT A : DTV101

PREV

NEXT

SELECT

Summary of Contents for i4 Inland
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands