manualshive.com logo in svg

Intellian i4 Inland, Installation And Operation User Manual

Share
Download
Intellian i4 Inland Installation And Operation User Manual Download Page 23

23

Introduction

This section of the handbook describes how to setup your Satellite TV 
System after installing the ACU. It includes the following functions:

• System start up.
• Changing the default satellite.
• Monitoring the antenna status.
• Setting sleep mode. 
• Entering setup mode.
• Setting the satellite pair.
• Editing satellite information.
• Setting the antenna parameter. 
• Setting the LNB local frequency.
• Setting GPS.
• Setting the DiSEqC method.
• Display versions.
• Display power status.
• Setting antenna go position.
• Setting antenna move step.
• Setting remote control. 
• Setting the factory default parameters.
• Performing diagnostic tests.

  Note: 

Many of the above functions will only be required only after 

  initial installation of your system. Refer to the Quick Installation Guide 
  before operating the system.

Operation Instruction

Summary of Contents for i4 Inland
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands