manualshive.com logo in svg

Intellian i4 Inland, Installation And Operation User Manual

Share
Download
Intellian i4 Inland Installation And Operation User Manual Download Page 18

18

Intellian Satellite TV Antenna Systems

Single Receiver Connection

1. Connect the RF cable 15m from the RF 1 connector on the
    antenna base plate to the ANT. RF1 connector on the ACU.
2. Connect the RF cable 3m from the RECEIVER connector on the 
    ACU to RF connector on the Receiver.
3. Connect the DC power cable 1.5m from DC power connector on 
    the ACU to a power source from 110~220V AC.
4. Press the POWER ON switch on the ACU to start the operation of the
    antenna system.

Figure 15 : Single Receiver Configuration

RF1 RF2

ANT RF1

FG        -     +

Antenna

ACU

Receiver

Adapter

( AC 110~220V )

RECEIVER

+

-

NMEA GPS

NMEA

PC INTERFACE

USB Cable

IRD 1

RF3 RF4

DC 24V

Connecting the System Cables

After installation and fixation of the antenna, connect the ACU to the antenna. 
Refer to the drawing below to connect cables.

Antenna RF Cable (Connecting Antenna - ACU)

Intellian provides the Antenna RF Cable (RG-6, 15 m) for connecting 
Antenna and ACU. Due to the signal losses across the length of the RF 
coax on L-Band, Intellian recommends the following 

75 Ω

 coax cable 

types for standard system installations. Check the instructions from the 
cable supplier. The table below shows the recommended cable types 
and maximum cable lengths for the antenna system. For installing 
cables longer than the recommended length, consult with Intellian 
Technologies first.

RF Cable Recommendation

Coaxial Cable Type

Max. Cable Length

RG-6/U Solid Copper Core or 
LMR 300

35 m

RG-11/U Solid Copper Core or 
LMR 400

60 m

LMR 600

100 m

Summary of Contents for i4 Inland
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands