Intellian i4 Inland Installation And Operation User Manual Download | Manualshive

Page: 27 / 63

background image

27

Sleep Mode

If the antenna loses the tracking satellite while in sleep mode, sleep
mode will be cancelled.

Setup Mode

Begin Setup Mode

To enter the Setup Mode simply follow the instructions below.

1. Press BACK to enter sleep mode.

2. Press BACK again for exiting sleep mode.

TRACKING A: DTV101

B: DTV119 SETUP

B: DTV119 SETUP

1. While the antenna is tracking press SETUP.

2. Press YES to enter setup mode.

3. Press YES to set the satellite pair.

TRACKING A: DTV101

SETUP MODE ?

SET SAT PAIR ?

PREV YES NEXT

B:DTV119 SETUP

NO

||

«
...
25
26
27
28
29
...
»

Summary of Contents for i4 Inland
































































Reviews:

No comments

Related manuals for i4 Inland

Brand: cahors Pages: 50

RBOmniTikG-5HacD

Brand: MikroTik Pages: 6

airMAX airGrid M5HP

Brand: Ubiquiti Pages: 28

Brand: Panorama Antennas Pages: 2

Brand: Alien Pages: 24

Brand: Strong Pages: 21

Brand: Hughes Network Systems Pages: 27

Brand: air MAX Pages: 16

Caravanman 65 Premium

Brand: Megasat Pages: 23

Brand: Megasat Pages: 56

Brand: Winegard Pages: 5

Brand: Trust Pages: 49

Brand: Shively Labs Pages: 78

Brand: Sirio Antenne Pages: 2

Brand: Sirio Antenne Pages: 2

Brand: Norsat Pages: 46

Brand: Vivax Pages: 44

Brand: Thrane&Thrane Pages: 63

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands