background image

General Installation Process

Note:

 Rack handles are required to install 

the bezel. For detailed instructions, see the 

Service Guide.

14

Install Rack Handles

8

RMM 4 NIC

Connector 

B

C

A

Chassis 

Back

Opening

Filler

A

Locate the RMM4 Lite connector close to the Riser Slot.

Carefully pick up the Intel

®

 RMM4 Lite module, match the alignment 

pin of the module and the connector on server board. Press to install.

Installing the Intel® RMM4 Lite

Push out and remove the 

metal cover on the chassis 

where the NIC RJ-45 

receptacle will align.

A

Position the module over 

the server board.

Fit the front of the 

module into the back 

panel slot.

Attach the module to the 

server board connector.

B

Secure the module with 

the two screws as 

shown.

C

Installing the Intel® RMM4 NIC

RMM4 Lite

Connector

17

Install Intel® Remote Management Module 4 (optional)

Add-in Card

Slots

Hooks 

13

Install Add-in Card Riser Assembly

Position the riser card edge 

connector over the server 

board riser socket and align 

the hook of the riser with the 

slot at the back of the chassis, 

then press straight down into 

riser socket.

I/O Connector 

I/O Module

A

B

C

D

15

Install Intel® I/O Expansion Module 
(optional)

A

D

B

Squeeze the sides of the filler panel to 

disengage it from the server system 

back panel and remove it.

Position the module over the server 

board, fit the front of the module into 

the back panel slot. 

Secure the module with the three 

screws as shown. 

C

Attach the module to the server 

board connector.

Note:

 If included, remember to install the EMI shield.

STOR_UPG_KEY

Locate the white 4-pin key, 

carefully pick up the Intel

®  

RAID 

C600 Upgrade Key. Match the 

key and connector orientation 

and press down to install.

Install Intel® RAID C600 
Upgrade Key 
(optional)

16

Summary of Contents for R1000SP





















Reviews: