manualshive.com logo in svg

Intel Core 2 Duo E4300, Design Manual, Page: 14 / 55

Share
Download
Intel Core 2 Duo E4300 Design Manual Download Page 14

Intel

®

 Core

TM

 2 Duo E6400, E4300, and Intel

®

 Pentium

®

 Dual-Core E2160 Processor—Processor

Thermal/Mechanical Information

Intel

®

 Core

TM

 2 Duo E6400, E4300, and Intel

®

 Pentium

®

 Dual-Core E2160 Processor

TDG

October 2007

14

Order Number: 315279 -003US

— The height of the package, from the package seating plane to the top of the 

IHS, and accounting for its nominal variation and tolerances that are given in 

the corresponding processor datasheet.

• Engages easily, and if possible, without the use of special tools. In general, the 

heatsink is assumed to be installed after the motherboard has been installed into 

the chassis.

• Minimizes contact with the motherboard surface during installation and actuation to 

avoid scratching the motherboard.

2.2

Thermal Requirements

Refer to the datasheet for the processor thermal specifications. The majority of 

processor power is dissipated through the IHS. There are no additional components, 

e.g., BSRAMs, which generate heat on this package. The amount of power that can be 

dissipated as heat through the processor package substrate and into the socket is 

usually minimal.

The thermal limits for the processor are the Thermal Profile and T

CONTROL

. The Thermal 

Profile defines the maximum case temperature as a function of power being dissipated. 

T

CONTROL

 is a specification used in conjunction with the temperature reported by the on-

die thermal diode and a fan speed control method. Designing to these specifications 

allows optimization of thermal designs for processor performance and acoustic noise 

reduction.

2.2.1

Processor Case Temperature

For the processor, the case temperature is defined as the temperature measured at the 

geometric center of the package on the surface of the IHS. For illustration, 

Figure 2

 

shows the measurement location for a 37.5 mm x 37.5 mm [1.474 in x 1.474 in] 775-

Land LGA processor package with a 28.7 mm x 28.7 mm [1.13 in x 1.13 in] IHS top 

surface. Techniques for measuring the case temperature are detailed in Section 3.4.

Note:

In case of conflict, the package dimensions in the processor datasheet supersedes 

dimensions provided in this document.

Summary of Contents for Core 2 Duo E4300
























































Reviews:

No comments