67
En
With this preference, you can protect your settings by
locking the setup menus.
Main menu
Lock Setup
■
Setup
`
Locked
`
Unlocked
When “
Locked
” is selected, the setup menus will be
locked and you cannot change any setting.
You can change various audio settings from the Home
menu (
➔
page 41
).
Note
• These settings are not available in either of the following cases:
– the “
Audio TV Out
” setting is set to “
On
” (
➔
page 64
).
– “
HDMI Control(RIHD)
” is set to “
On
” (
➔
page 64
) and
you’re listening through your TV speakers.
Sound Program
■
Sound Program
`
Stereo Source 1
,
Stereo Source 2
,
Stereo Source 3
,
Multich Source 1
,
Multich Source 2
,
Multich
Source 3
`
Off
With this setting, you can select the combination of
settings that you registered in “
Sound Program Edit
”
(
➔
page 55
).
Note
• This setting is not available when the multichannel analog input
is selected.
• If the input selector is changed, the “
Sound Program
” setting is
switched back to “
Off
”.
Tone Control Settings
■
Bass
`
–10dB
to
0dB
to
+10dB
in 2 dB steps.
You can boost or cut low-frequency sounds output.
■
Treble
`
–10dB
to
0dB
to
+10dB
in 2 dB steps.
You can boost or cut high-frequency sounds output.
You can adjust the bass for the front, front wide, front
high, center, surround, surround back and subwoofer
speakers and treble for the front, front wide, front high,
center, surround and surround back speakers, except when
the Direct or THX listening mode is selected.
Operating on the AV receiver
Note
• This setting is not available when the multichannel analog input
is selected.
Speaker Levels
■
Subwoofer 1
`
–15.0dB
to
0.0dB
to
+12.0dB
in 0.5 dB steps.
■
Subwoofer 2
*1
`
–15.0dB
to
0.0dB
to
+12.0dB
in 0.5 dB steps.
■
Center
`
–12.0dB
to
0.0dB
to
+12.0dB
in 0.5 dB steps.
You can adjust the volume of each speaker while listening
to an input source.
These temporary adjustments are cancelled when the AV
receiver is set to standby. To save the setting you made
here, go to “Level Calibration” (
➔
page 51
) before
setting the AV receiver to standby.
Note
• You cannot use these functions while the AV receiver is muted.
• These settings cannot be used while a pair of headphones is
connected.
• Speakers that are set to “
No
” or “
None
” in
“Speaker Configuration” (
➔
page 50
) cannot be adjusted.
*1
If the “
Subwoofer
” setting is set to “
1ch
”, this setting cannot
be selected (
➔
page 50
).
Lock Setup
Using the Audio Settings
1
Press
Receiver
followed by
Home
.
2
Use
q
/
w
and
Enter
to select “Audio”, and then use
q
/
w
/
e
/
r
to make the desired selection.
1
Press
Tone
repeatedly to select either “Bass” or
“Treble” for each speaker or subwoofer.
2
Use
+
and
–
to adjust.
Summary of Contents for DTR-70.3
Page 1: ...AV Receiver DTR 80 3 DTR 70 3 Instruction Manual...
Page 106: ...106 En Memo...
Page 107: ...107 En Memo...
