Integra DTR-70.3, Instruction Manual

Page: 56 / 108

56
En
Note
• “ Listening Mode ” is only available when the input signal
matches the setting of “ Sound Program ”.
• “ Music Optimizer ” is only available when “ Stereo Source 1 ”,
“ Stereo Source 2 ” or “ Stereo Source 3 ” is selected.
• When “ Audyssey Quick Start ” has been used for measurement,
the “ Audyssey ”setting cannot be selected.
*1 You cannot select the “ Subwoofer ” setting if you set to “ No ”
in the “ Speaker Configuration ”.
*2 This setting cannot be used when the “ Listening Mode ”
setting is set to “ Direct ”.
*3
To enable this setting, you must first perform the Room
Correction and Speaker Setup.
Items can be set individually for each input selector.
Main menu Source Setup
Audyssey
■
Audyssey
`
Off
`
Movie :
Select this setting for movie material.
The
Audyssey indicator lights.
`
Music :
Select this setting for music material.
The
Audyssey indicator lights.
Note
• If the “ Audyssey ” setting is set to “ Off ”, the “ Equalizer ”
settings are applied (
➔
page 52 ).
• When “ Audyssey Quick Start ” has been used for measurement,
the “ Audyssey ” setting cannot be selected.
• Audyssey equalizing does not work with DSD sources.
■
Dynamic EQ
`
Off
`
On :
Audyssey Dynamic EQ ® becomes active.
The Dynamic EQ indicator lights.
With Audyssey Dynamic EQ, you can enjoy great sound
even when listening at low volume levels.
Audyssey Dynamic EQ solves the problem of
deteriorating sound quality as volume is decreased by
taking into account human perception and room acoustics.
It does so by selecting the correct frequency response and
surround volume levels moment-by-moment so that the
content sounds the way it was created at any volume level
— not just at reference level.
■
Reference Level
Audyssey Dynamic EQ Reference Level Offset
`
0dB :
This should be used when listening to movies.
`
5dB :
Select this setting for content that has a very wide
dynamic range, such as classical music.
`
10dB :
Select this setting for jazz or other music that has a
wider dynamic range. This setting should also be
selected for TV content as that is usually mixed at
10 dB below film reference.
`
15dB :
Select this setting for pop/rock music or other
program material that is mixed at very high listening
levels and has a compressed dynamic range.
Movies are mixed in rooms calibrated for film
reference. To achieve the same reference level in a
home theater system each speaker level must be
adjusted so that –30 dBFS band-limited (500 Hz to
2000 Hz) pink noise produces 75 dB sound pressure
level at the listening position. A home theater system
automatically calibrated by Audyssey MultEQ XT32
will play at reference level when the master volume
control is set to the 0 dB position. At that level you can
hear the mix as the mixers heard it.
Audyssey Dynamic EQ is referenced to the standard
film mix level. It makes adjustments to maintain the
reference response and surround envelopment when the
volume is turned down from 0 dB. However, film
reference level is not always used in music or other non-
film content. Audyssey Dynamic EQ Reference Level
Offset provides three offsets from the film level
reference (5 dB, 10 dB, and 15 dB) that can be selected
when the mix level of the content is not within the
standard.
Note
• If “ Dynamic EQ ” setting is set to “ Off ”, these technologies
cannot be used.
Source Setup
Preparation
Press the input selector buttons to select an input source.
The tone for each speaker is set automatically by
Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup. To enable the following settings, you
must first perform the Room Correction and Speaker
Setup (
➔
page 31 ).
These technologies cannot be used when:
• a pair of headphones is connected, or
• Direct listening mode is selected.