background image

                                                                                                                                  Page 12 of 22                                                                                         Rev: 9/30/2011 1:26 PM 

 

Installation 

CAUTIONS AND WARNINGS

 

Read and understand these instructions before installing and retain them for future reference. 

IMPORTANT!

 

If you are not knowledgeable about, and comfortable with, HVAC circuitry, you should have a qualified HVAC professional install 
TempLinc for you. 

 

 

Tools Needed 

Flat blade screwdriver 

 

Wire cutter / stripper  

Preparation 

Proper installation of the thermostat will be accomplished by following these step by step instructions. If 
you are unsure about any of these steps, call a qualified technician for assistance.  

1)  Make sure your Heater/Air Conditioner is working properly before beginning installation of the 

thermostat 

2)  Carefully unpack the thermostat. Save the screws, bracket and instructions 

3)  Turn off power to the Heating/Air Conditioning system at the main fuse panel. Most residential system 

have a separate breaker for disconnecting power to the furnace 

4)  Remove the cover of the old thermostat. If it does not come off easily check to see if it is mounted 

with screws. 

5)  Loosen the screws holding the thermostat base or subbase to the wall, and lift away 

6)  Disconnect the wires from the old thermostat. Tape the ends of the wires as you disconnect them, 

and mark them with the letter of the terminal for easy reconnection to TempLinc. 

7)  Keep the old thermostat for reference purposes, until you new thermostat is functioning properly 

Wire Connections 

If the terminal designations on your old thermostat do not match those on TempLinc, refer to the chart 
below or the wiring diagram that follows. 
 

Wires from old 

thermostat terminal 

Function 

Install on TempLinc 

connector  

 

Common 24V 

24V COM 

 

Power 24V 

24 RH 

 

Power 24V 

24 RC 

 Heat 

1 W1 

 

Heat 2  

W2 

 Fan  G 

 Cooling 

1  Y1 

 

Cooling 2  

Y2 

Summary of Contents for TempLinc 2441T
























Reviews: