manualshive.com logo in svg

innovair MULTI-MAX VWM10H25F, Owner'S Manual

Share
Download
innovair MULTI-MAX VWM10H25F Owner'S Manual Download Page 33

 

MULTI-MAX

 HIGH WALLS

OWNERS MANUAL

Check after installation

Items to be checked

Possible malfunction

The unit may drop, shake or emit noise.

Have you done the refrigerant leakage 

test?

(heating) capacity.
It may cause condensation and water 

dripping.

Is water drained well?

It may cause condensation and water 

dripping.

Is the voltage of power supply accord-

ing to the voltage marked on the

nameplate?

It may cause malfunction or damaging 

the parts.

Is electric wiring and pipeline installed

correctly?

It may cause malfunction or damaging 

the parts.

Is the unit grounded securely?

It may cause electric leakage.

Does the power cord follow the speci-

It may cause malfunction or damaging 

the parts.

Is there any obstruction in the air inlet 

and outlet?

(heating) capacity.

The dust and sundries caused during 

installation are removed?

It may cause malfunction or damaging 

the parts.

The gas valve and liquid valve of 

connection pipe are open completely? (heating) capacity.

30

Summary of Contents for MULTI-MAX VWM10H25F









































Reviews:

No comments

Brands by name

Popular brands

Load more brands