manualshive.com logo in svg

Innova Ephoca HPAC 2.0, Installation Manual

Share
Download
Innova Ephoca HPAC 2.0 Installation Manual Download Page 2

2

ATTENTION 

Please read this entire guide (both the installation and operation portions) thoroughly prior to installation. Pay careful 

attention to all safety warnings and notices.

As a professional installer you have an obligation to know the product better than the customer. We cannot 

overemphasize the importance of proper installation.

It is the installer’s responsibility to properly install the unit. Installation must be in conformance with all applicable local 

and/or national codes.

Often during installation or repair it is possible to place yourself in a position which is more hazardous than when the 

unit is in operation.

It is your responsibility to install the system safely and to know it well enough to be able to instruct a customer in its 

safe use. The precautions listed in this Installation Manual are intended as supplemental to existing practices. However, 

if there is a direct conflict between existing practices and the content of this manual, the precautions listed here take 

precedence.

 WARNING

READ AND FOLLOW THIS MANUAL

Please read this manual thoroughly prior to installation and 

operation. Failure to do can result in damage to the unit, damage 

to property, personal injury or death

 WARNING

EXCESSIVE WEIGHT HAZARD

Use two people when lifting and installing the unit. The unit is 

unbalanced on the right (compressor side) Failure to do can result 

in back or other injury.

Summary of Contents for Ephoca HPAC 2.0









































Reviews:

No comments

Brands by name

Popular brands

Load more brands