INIM Electronics SmartLink Advanced Series Installation And Programming Manual Download Page 36

Page: 36 / 40

Events

Telephone dialler

Appendix A

EVENTS

An event is a condition recognized by the SmartLinkAdv; each event

is characterized by an activation (when an event occurs) and a

restoral (when the event ends).
The following table shows the events the control panel recognizes,

the number of events for each type, the trigger and restoral method

of each event and whether the event is a pulse event (pulse events

restore automatically soon after activation).

Table 7-3:

Event type

Name

Occurs when...

Restores when ...

Number of

events

Pulse

events

Zone alarm

A zone generates an alarm

A zone restores

One event for

each zone

Terminal tamper

A terminal detects tamper

(short-circuit or wire cutting)

A terminal restores

One event for

each terminal

Generic alarm

At least one zone is generating

an alarm

All the zones have reset

Real-time zone

The electrical status of a zone

switches from standby to alarm

The electrical status of a zone

switches from alarm to

standby

One event for

each zone

The event is independent of the zone type and the armed/

disarmed status.

Not ready to arm A zone is not in standby status

All the zones are in standby

status.

Away arming

request

A request is made to arm in

Away mode

A request is made to disarm

the partition

Yes

Stay arming

request

A request is made to arm in

Stay or in Instant mode

A request is made to disarm

the partition

Yes

Arming effective

SmartLinkAdv is effectively

armed in Away mode

SmartLinkAdv is effectively

disarmed

Stay arming

effective

SmartLinkAdv is effectively

armed in Stay or Instant mode

SmartLinkAdv is effectively

disarmed

Memory reset

Memory reset is requested

Yes

Exit time

The exit time is running

The exit time expires

Entry time

The entry time is running

The entry time expires

Valid user-code

recognized

A PIN entered at a keypad is

recognized as valid

One event for

each code

Yes

Open-panel

tamper

The SmartLinkAdv frontplate is

removed

The SmartLinkAdv frontplate

is closed

Low battery

The backup-battery voltage is

below 10.7V

The backup-battery voltage is

over 11.74V

Battery fault

The backup battery is low

The backup battery is charged

Battery not

connected

Battery not detected or

disconnected

Battery connected

Summary of Contents for SmartLink Advanced Series









































Search results

Summary of Contents for SmartLink Advanced Series

Reviews:

Related manuals for SmartLink Advanced Series

Brands by name

Popular brands

INIM Electronics SmartLink Advanced Series, Installation And Programming Manual

Search results

Summary of Contents for SmartLink Advanced Series

Reviews:

Related manuals for SmartLink Advanced Series

Brands by name

Popular brands