background image

6.  General information

6.5  Documents for the users

Declarations of Performance, Declarations of Conformity and Certificates concerning to Inim Electronics 

S.r.l. products may be downloaded free of charge from the web address www.inim.biz, getting access to 

Extended Access and then selecting "Certifications" or requested to the e-mail address [email protected] or 

requested by ordinary mail to the address shown in this document.

Manuals may be downloaded free of charge from the web address www.inim.biz, getting access to the 

reserved area, after the login, and then to the section of each product.

6.6  WEEE

Informative notice regarding the disposal of electrical and electronic equipment (appli-
cable in countries with differentiated waste collection systems)

The crossed-out bin symbol on the equipment or on its packaging indicates that the product must be 

disposed of correctly at the end of its working life and should never be disposed of together with gene-

ral household waste. The user, therefore, must take the equipment that has reached the end of its working 

life to the appropriate civic amenities site designated to the differentiated collection of electrical and elec-

tronic waste. As an alternative to the autonomous-management of electrical and electronic waste, you can 

hand over the equipment you wish to dispose of to a dealer when purchasing new equipment of the same 

type. You are also entitled to convey for disposal small electronic-waste products with dimensions of less 

than 25cm to the premises of electronic retail outlets with sales areas of at least 400m2, free of charge and 

without any obligation to buy. Appropriate differentiated waste collection for the subsequent recycling of the 

discarded  equipment, its treatment and its environmentally compatible  disposal helps to  avoid  possible  

negative effects on the environment and on health and favours the re-use and/or recycling of the materials it 

is made of.

Information  about  disposal  of  batteries  and  accumulators  (applicable  in  Countries  
with separate collection systems)

This marking on batteries and/or their manual and/or their packaging, indicates that batteries of this 

products, at the end of their working life, should not be disposed of as unsorted municipal waste, but must 

be object of a separate collection. Where marked, the chemical symbols Hg, Cd o Pb indicate that the bat-

tery contains mercury, cadmium or lead above the reference levels of the directive 2006/66/EC. If batteries 

are not properly disposed of, these substances, together with other ones contained, can cause harm to 

human health and to the environment. To protect human health and the environment, to facilitate treatment 

and recycling of materials, separate batteries from other kind of waste and use the collection scheme stated 

in your area, in accordance to current laws. Before disposing of the above, it's appropriate to remove them 

from their holders avoiding to damage them or causing short circuits.

16

Installation and programming manual- 100-DRAFT

Summary of Contents for Air2-BS200





















Reviews: