background image

MAINTENANCE SECTION

15

 PART NUMBER FOR ORDERING

2400P

3000P

31

Motor Case Cover Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2400P–A202

3000P–A202

32

Suspension Hole Liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

1100P–232

1100P–232

33

Motor Case Cover Gasket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2400P–739

3000P–739

34

Motor Case Cover Screw (4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2400P–277

3000P–638

35

Cover Screw Lock Washer (4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  EQ112P–58

EQ112P–58

Hammer Case Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2400P–A727

3000P–A727

36

Hammer Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

2400P–727

3000P–727

37

Hammer Case Bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

EQ110P–641

3000P–641

38

Adjustment Hole Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

500P–95

500P–95

39

Hammer Case Gasket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2400P–740

3000P–740

40

Hammer Case Cap Screw (4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2400P–277

3000P–638

41

Cap Screw Lock Washer (4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  EQ112P–58

EQ112P–58

42

Dead Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  –––

EQ230P–A48

43

Rubber Housing Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2400P–2

3000P–2

44

Nameplate

for models ending in –EU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  ––––––

3000P–EU–301

for all other models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400P–301

3000P–301

*

Forward Rotation Label (for models ending in –EU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  ––––––

7802R–EU–F99

*

Reverse Rotation Label (for models ending in –EU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  ––––––

7802R–EU–R99

45

Nameplate Screw (2 for 2400P; 4 for 3000P) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  EQ106S–322

EQ106S–322

46

Warning Label

for models ending in –EU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  ––––––

EU–99

for all other models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WARNING–2–99

WARNING–2–99

47

Oil Daily Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  500P–69

500P–69

48

Two Speed Trigger  Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  180PQ–68

180PQ–68

*

Motor Tune–up Kit (includes illustrated items 24, 28, 30 and 33) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2400P–K500

3000P–K500

*

Not illustrated.

Summary of Contents for 2400P
























Reviews: