Ingecon SUN 125 TL U 208 Outdoor Installation Manual Download Page 77 | Manualshive

Page: 77 / 88

Ingecon SUN 125 TL U 208 Outdoor Installation Manual Download Page 77

ABB2000IKI01

77

Installation manual

Ingeteam

V

A1

J18

J13
J14

J12

J3

J4

J21

J5

J6

J7

J8

J19

J28

J27

J16

J31

J17

J15

J11 J10

J20

J32

J1

V

A2

V

A3

Intake board

9.4.2. Temperature

Code

Alarm

Reason for shutdown

Description

0020H

Temperature

Power electronics temperature.

The power electronics exceeds 176 °F (80 °C).

Auxiliary temperature sensor

The auxiliary temperature sensor has triggered an alarm

In the event of a shutdown with reason “Motivo Paro Temperatura”, the first step is to check if the 0020H alarm
persists. If so, check the temperature of the unit’s radiator via the display menu:

MONITORING

TempRad

•

If the temperature displayed is close to or above 80 degrees, the unit has failed to inject power as a precau-

tion against a potentially damaging radiator temperature for the unit. The inverter will remain in this state until the
radiator has cooled, and then it will reconnect to the network.

If the problem occurs frequently, you should check the ventilation (fans and air intake grills) of the inverter and the
enclosure in which it is installed.

•

If the temperature shown is less than 140 °F (60 °C) and the alarm persists, the problem could be in the

«
...
75
76
77
78
79
...
»

Summary of Contents for SUN 125 TL U 208 Outdoor

























































































Reviews:

No comments